Products not found
The switch cabinet temperature controller has been specially designed for the supervision and control of temperatures in switch cabinets, drinks or cash dispensers etc. and is installed on a DIN EN 60715 compliant standard rail. It can be installed independent of its position. However, care must be taken to install it in no other but an enclosure that complies with the protection class admitted for this purpose, such as a switch cabinet for example. In cases where the controller, for reason of space, must be installed close to heat or refrigeration sources or where it, for some other reasons, cannot be installed at the exact measuring point directly, the capillary controller with remote sensor must be used.
price by request
Available
The JTF is a fail-safe frost protection thermostat. The device has been specially designed for anti freezing protection purposes. It detects the temperatures in air or water flows around or inside of warm water heating spirals and heat exchangers in ventilation-, heating- and/or air conditioning systems and triggers the corresponding control commands. With this thermostat, the adjusted set value can be protected against misadjustment by applying a lead seal. All devices of this series have been tested and certified by the TÜV (Association for Technical Inspection) in compliance with DIN EN 14597
price by request
Available
Universal capillary controller RTKSA-0xx.xxx
This range of devices was developed especially for use in heating technology in boiler systems or storage units, district heating transfer stations and heat transfer systems, for use in ventilation technology as supply air monitoring or as cut-outs for electric heating coils and to control and monitor temperatures on pipes and containers.
Room controller RTKSA-1xx.xxx
The room controller were developed especially for use in industrial and trade fair halls, air-inflated structures and greenhouses. If used as frost protection controller, the higher tolerances at the end of the scale should be noted.
Frost protection controller RTKSA-2xx.xxx
The frost protection controller were developed especially for ensuring air-side or water-side frost protection in hot water heating coils and heat exchangers in ventilation, heating or air conditioning systems.
price by request
Available
Minimum or maximum thermostat for supply air monitoring and fan control in ventilation and air conditioning systems.
price by request
Available
This device series has been specially designed for use as a minimum- or maximumvalue thermostat for the monitoring of inlet air and control of fans in ventilation and air-conditioning systems. As an overheat protection thermostat for control of electric heating registers and air heaters directly fired with oil or gas.
price by request
Available
Contact thermostat for controlling or monitoring temperatures at heating coils, pipelines, or containers, e.g. temperature-dependent pump control or control of motor valves.
price by request
Available
This temperature controller has been specially devised for the triggering of Peltier modules, which are usually applied in connection with the heating or cooling control operations performed in switch cabinets, ticket machines or cash dispensers or for the emission of heating and cooling messages or requests.
price by request
Available
This temperature controller has been specially devised for the triggering of Peltier modules and fans that are usually applied in connection with the conditioning of the air in switch cabinets.
The KTRRN is equipped with two control ranges, i.e. one each for the function “heating” and “cooling”. The selection of the “heating” switch point takes place in the lower section of the setting range, while the one of the “cooling” switch point is effected in the upper section of the range. The setting ranges are separated by a span that is equivalent to10K. A neutral zone of at least 10K is thus created.
price by request
Available
Contact thermostat for controlling or monitoring temperatures at heating coilFor monitoring or regulation of the temperature of liquids and not aggressive gaseous mediums. For heating and ventilation applications, cooling and air conditioning systems and general industrials uses.
JET- … R
For monitoring of regulation of the temperature in coldstorage rooms, for control of airheaters in greenhouses, industrial sheds, sports halls and inflatible buildings.
The units JET-110 RF and JET-120 RF are particulary suitable for out door applicationss, pipelines, or containers, e.g. temperature-dependent pump control or control of motor valves.
price by request
Available
Control and monitoring of temperatures of certain outdoor areas, e.g. driveways or wet rooms (greenhouses, halls, storage and cellar rooms, garages, etc.).
price by request
Available