Products not found
Temperature sensor suitable for measurement of pipes and shafts. Rigid sheath is joined to radiator enhancing the area of heat reception. Sensor has a band clamp that enables permanent radiator installation on pipe or shaft.
- radiator enhancing surface of heat reception with band clamp for mounting on a pipeline DN 15÷200 mm
- insulated hot junction SO
- material: brass
price by request
Available
Temperature sensor in Alnico type magnet suitable for measurement of steel surfaces. Magnet application enables quick and easy installation of sensor on steel surface where temperature is to be measured.
- mounting: Alnico
- max. working temperature: 450 °C (above 180 °C the paint coat is burnt out)
- sensor sheath mounted with magnet
- material: stainless steel 1.4541
price by request
Available
Series 5 General Purpose Thermocouples are low cost and offered in a variety of configurations. Tip temperatures can be as high as 450°C (842°F) for fiberglass insulated wire, or 200°C (392°F) for FEP insulated wire. For higher temperatures limits, or cover head assemblies, see Series 8 Mineral Insulated Thermocouples.
Retail price from $36.25
Available
The Series WTP-R Wireless Remote Probe Temperature Sensors can be used to monitor surface temperature of water lines or in locations where space is limited. For greater flexibility, the enclosure for the electronics can be mounted up to 25′ from the temperature measurement point. By sampling the temperature measurement every 10 seconds, the battery is able to power the unit for up to 8 years.
Retail price from $467,8
Available
INJECTION MOLDING NOZZLE TYPE
In-Melt type thermocouples and RTDs are designed to bolt into the injector nozzle and sense the temperature of the melt directly, and is rated to 450°C (900°F). The standard 3/8″ hex head stainless steel body has 3/8-24 NFT threads. The sensor tip extends 1/8″ beyond the end of the bolt assembly.
Retail price from $83.3
Available
TheSeries TE-WSS Stainless Steel Wall Plate Temperature Sensor measures the ambient air temperature in classrooms and industrial environments.
Retail price from $12,1
Available
The Series TE Duct and Immersion Temperature Sensor can be used to monitor air or water temperature throughout a building management system or an air handler unit. Flanged duct sensors monitor the supply or return air and provide a thermistor or RTD output to the digital controller. Immersion sensors which are supplied with compression fittings are typically used to monitor the hot or chilled water lines throughout a building. Thermowells are recommended, but not required on the immersion sensors.
Retail price from $10,1
Available
Series 9 Special Application Thermocouples & RTDs cover a wide variety of types and configurations. This section covers FEP covered thermocouples and RTDs in rigid and flexible types, ring type thermocouples and RTDs for surface measurement, web type thermocouples for surface measurement of moving objects such as rollers, and penetration thermocouples and RTDs with sharp tips for measurement of viscous liquids and semisolids such as tar and heavy oil, and other material such as frozen food and meat.
Retail price from $18,35
Available
The Series S2 Surface Mount Temperature Sensor provides a cost effective and reliable solution for surface contact temperature measurement of conditioned water pipes, low pressure steam or refrigerant lines.
Retail price from $54,85
Available
The Series RHRS Radiation Shield protects outside air humidity transmitters from rain and radiated heat. With the curved shape and color of the plates, air flow is able to move across the sensor to keep radiated temperatures from rooftops and surrounding surfaces from affecting humidity readings.
Retail price from $53,65
Available
The Model A-709 Temperature Transmitter Enclosure can be used to mount our Series 651, 659 and Model TBU-00 transmitters to any of our 1/4″ diameter temperature sensors. The screw on enclosure cover can be quickly removed and has a chain to prevent it from getting lost. The Model A-709 comes with the necessary adapters and fittings for attaching the temperature sensor.
Retail price from $59,8
Available
The Series TE-OND/TE-RND/TE-OSA Outdoor Temperature Sensors are offered different configurations to increase measurement accuracy by reducing radiated heat effects. For applications where the north side of the building is accessible, the TE- OND/TE-OSA can be used to protect against low levels of radiated heat.
Retail price from $28,65
Available
The Series 651 Temperature Transmitter is designed for use with 2 or 3 wire Pt100 RTDs or ungrounded Type K thermocouples. Thermocouple models 651TC are cold junction compensated, automatic 32 to 160°F (0 to 70°C) with upscale burnout.
Retail price from $188.85
Available
The Series TE-SNW Weather Resistant Surface Temperature Sensor non- intrusively measures the process temperature in hot and cold water loops in buildings. In order to work with most common building controllers, the output of the sensor can be chosen from 6 different RTD and Thermistor curves.
Retail price from $40,75
Available
The Series 659 Push-Button Temperature Transmitters accept thermocouple (J, K, T), RTD (Pt100Ω) or thermistor input and provide a linearized 4 to 20 mA output. The transmitter is quickly ranged and calibrated by using a single on-board switch. An LED provides visual indication of sensor fault and programming mode. Models feature reverse polarity protection. Thermocouple models are also galvanically isolated and cold junction compensated.
Retail price from $188.35
Available
The Series ILA In-Line IR Sensors, measure temperatures from 32 to 932°F (0 to 500°C) and provide a linear 4 to 20 mA, or thermocouple output. The 2-wire signal is compatible with almost any indicator, controller, recorder, data logger, etc., without the need for special interfacing or signal conditioning. They are suitable for most materials such as food, paper, textiles, plastics, leather, tobacco, pharmaceuticals, chemicals, rubber, coal, and asphalt.
Retail price from $506,7
Available
The Series TE-E/N Wall Mount Temperature Sensors provide a low cost temperature input for any building management system.
For models with resistive thermistors or RTD outputs, see Resistance vs. Temperature Table.
Retail price from $12,9
Available
The Series BTO Bimetal Thermometer with Transmitter Output eliminates the need for a separate thermometer and transmitter. By only needing one connection, the BTO series reduces installation cost and saves space. The head-mount transmitter is located in a weatherproof thermal head located on the side of the stem. The BTO series is ideal for use on power generating boilers, skid mounted compressors, and thermal oxidation systems.
Retail price from $930
Available
The Series O-4 Outside Air Temperature Sensors are great for monitoring ambient air temperatures in outdoor applications. The temperature sensors are mounted in a NEMA 4X enclosure with integral mounting tabs. The mounting tabs can be used to surface or suspension mount the temperature sensors. The removable terminal block makes installation easy. The Series O-4 can be used to measure outside air temperatures in building automation systems or room temperatures inside agricultural ventilation houses.
Retail price from $14,7
Available
The Series TTE Explosion-Proof RTD Temperature Transmitter is the ideal product for hazardous temperature measurement applications. The TTE series has seven preprogrammed temperature ranges that are selectable via an internal dip switch. For those applications that need a custom range, the transmitter can be easily configured for any range between -30 to 250°F with a minimum span of 40°F. The span and zero can be quickly adjusted with a simple push button design. The compact housing allows for the transmitter to be mounted in virtually any application.
Retail price from $644.8
Available
The Series CC1 Averaging Temperature Sensor Clips are used to mount the capillary of the AVG series temperature sensor to the wall of the duct or air handler. The clips are available in gray or a natural color. The clip can hold 1/8″, 1/4″ or 3/8″ capillary diameters. The top of the mounting clip can also be used to hold a single 1/4″ diameter temperature probes in place. Slots are provided for using nylon zip ties to hold the tubing in place, if needed.
Retail price from $1,95
Available
The Series R Mineral Insulated RTD’s are known for their excellent mechanical durability and resistance to electrical breakdown. Probe sheaths can be bent most any angle without special equipment. The Series R RTD’s are offered in a variety of configuration to meet your application. For smaller sheath diameters, and transition fitting is used between the cold end of the sheath and the extension wires. This fitting is 1-1/4″ long by 1/4″ OD for 1/8″ and smaller sheath diameters, 1-1/2″ long by 3/8″ OD for 3/16″ and 1/4″ sheath diameters. Tip temperatures can be as high as 650°C (1202°F), while fiberglass extension wire is limited to 450°C (842°F).
Retail price from $174,8
Available
The Series TTW Weatherproof Immersion Temperature Transmitter offers a field adjustable temperature transmitter pre-assembled with an RTD sensor and weatherproof enclosure.
Retail price from $345.7
Available
The Series S2-2 General Purpose Surface Temperature Assembly is ideal for monitoring the temperature of indoor distribution lines when it is not possible to penetrate the pipe. The plastic housing is in the shape of a standard junction box with multiple knockouts for easy conduit access. The strap-on connection quickly wraps around a pipe and can be securely tightened using a flat head screw driver. The Series S2-2 can be ordered with a choice of 11 output options that allow it to communicate to any standard building control system.
Retail price from $73,25
Available